公司新聞
道路瀝青在生產過程中應該注意幾點
來源：http://www.xiuxiuys.com/ 日期：2023-06-28
道路瀝青在生產過程中應該注意以下幾點：一，不能超量加料。這樣會使加料的速度變慢；二，不能超量進行加工。三，不能超量進行加工。這樣，就可以避免一些題發生。此外，要注意不同材料之間的磨擦力和摩擦力。
During the production process of road asphalt, the following points should be noted: firstly, excessive feeding is not allowed. This will slow down the feeding speed; 2、 Excessive processing is not allowed. 3、 Excessive processing is not allowed. In this way, some problems can be avoided. In addition, attention should be paid to the frictional force and friction force between different materials.
石油類、瀝青性能好、質量高、耐腐蝕性強，而且石油類的調和材料在生產過程中也會出現一些題。如果沒有合理地選擇調整材料，就很難達到優良的道路結構。所以在選擇調整材料時，要考慮道路瀝青質量。因為道路的結構是由石油類、瀝青類等組成的。
Petroleum and asphalt have good performance, high quality, and strong corrosion resistance, and some problems may arise in the production process of petroleum blending materials. If there is no reasonable selection and adjustment of materials, it is difficult to achieve excellent road structure. So when selecting and adjusting materials, it is necessary to consider the quality of road asphalt. Because the structure of roads is composed of petroleum, asphalt, etc.
調和的方法是將瀝青的調和部分用水泥或者砂漿，用熱熔膠粘在一起，然后用高壓噴霧器進行噴射，在這種噴霧器上可以使得瀝青的調整效果非常好。如果不注意，很容易發生。這個時候要注意保持清潔。
The method of blending is to use cement or mortar to stick the blended parts of asphalt together with Hot-melt adhesive, and then spray them with a high-pressure spray. This spray can make the adjustment effect of asphalt very good. If not paid attention, it can easily happen. At this time, it is important to maintain cleanliness.
另外還有一點要注意就是不能讓瀝青在高溫下發生破壞性變形。因為瀝青在高溫下的發生變形是一種很危險的事情，這個時候要注意保持清潔。瀝青在加工時要盡量避免瀝青中摻有水分，這樣就可以減少瀝青中有機物和水分對路面造成破壞。
Another thing to note is that asphalt cannot undergo destructive deformation at high temperatures. Because the deformation of asphalt at high temperatures is a very dangerous thing, it is important to keep it clean at this time. When processing asphalt, it is important to avoid the addition of moisture to the asphalt as much as possible, in order to reduce the damage caused by organic matter and moisture in the asphalt to the road surface.
另外，還應該注意瀝青表面是否有一層透明膠狀物。如果表面有水分，則應該用干燥劑或是其他潤滑劑來消除水分。瀝青在加工過程中的表層是否會發生變形。瀝青的含水率一般在40％～60％左右，瀝青表面是否有氧化、脫膠等現象都可能影響到路面的養護和使用。
In addition, attention should also be paid to whether there is a layer of transparent adhesive on the asphalt surface. If there is moisture on the surface, a desiccant or other lubricant should be used to eliminate the moisture. Will the surface of asphalt deform during processing. The moisture content of asphalt is generally around 40% to 60%, and the presence of oxidation, debonding, and other phenomena on the asphalt surface may affect the maintenance and use of the road surface.
濟南瀝青生產廠家在生產加工時，要做好調和的準備。先是調整好道路瀝青的質量。當然，調整好瀝青的質量是非常重要的。如果你沒有做到，那就不能說這個調和就是合格產品。
Jinan asphalt manufacturers should prepare for blending during production and processing. Firstly, adjust the quality of road asphalt. Of course, adjusting the quality of asphalt is very important. If you haven't achieved it, then you can't say that this reconciliation is a qualified product.
其次，對于調和后的瀝青進行測試。這一步需要考慮很多因素。比如它在運輸中會不會發生損壞。調和的方法是先用一個大鐵錘將瀝青攪拌，再將瀝青放在水中，攪勻后放入鍋內加熱。
Secondly, test the blended asphalt. This step requires considering many factors. For example, will it be damaged during transportation. The method of mixing is to mix the asphalt with a big hammer, then put the asphalt in water, mix it well and put it into a pot for heating.
如果不能夠正確操作的話，就應該用一根木棒把水倒進去。如果不能夠控制好的話，可以先用木棒將其擊碎。還要注意使調和好后的瀝青在運輸過程中不要有任何變形。更多相關事項就來我們網站http://www.xiuxiuys.com進行咨詢了解吧!
If it cannot be operated correctly, a wooden stick should be used to pour water in. If it cannot be controlled properly, it can be broken first with a wooden stick. Also, pay attention to ensuring that the mixed asphalt does not deform during transportation. For more related matters, come to our website http://www.xiuxiuys.com Consult and learn more!
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：